Outdoor shades are standardly motorized with XQ5 Premium Radio Controlled Motors with a built in radio receiver. These motors have a 5 year warranty. They are cost effective and reliable and have all the options of Somfy motors EXCEPT they do not work with home automation. If you need home automation, you will need to order the Somfy Motors. As with all motors, the factory programs the remotes to the motors and you merely set the limit stops. Instructions for programming limit stops are found on the Installation/Videos tab. Motors can be ordered on the left or the right. XQ5 Motors come with an 8’ power cord. (16’4” and 32’9” power cords are available.) Somfy Motors come with a 6’power cord. (12', 18', and 24' power cords are available.)
Motors plug into grounded outlets. You may hard wire them, but must install a shut off switch for each motor so you can disconnect each motor from power separately should you ever need to reprogram. Motors are 120V and draw about 1.6 amps. Outdoor shades with motors are best ordered with housing boxes to prevent water from getting into the motor. Make sure you create a drip loop to keep water from running down the cord into the motor head. (This means you run the power cord down from the motor and then up to the outlet so the water will drip off the bottom of the cord and can't run up the cord.) Operating temperature range for motors is 14 degrees F to 104 degrees F (-10 degrees C to 40 degrees C.) If you are installing your shade in a completely weather tight pocket, you may order a motorized shade with exposed roll brackets. Call for pricing.
With the XQ5 Premium Motors, you can cut the power cord as short as you want because the antenna is not the ground wire. For Somfy Motors you cannot cut it shorter than 3 feet.
Remotes and surface mounted wall switches are all wireless. They enable you to control one or more motors with one receiver. They are either single channel when ordering just one shade or multi channel which can operate each shade individually or as a group. See Motor Accessories Link for more information.
XQ5 Premium Motor Controls
White slim line remote
Black slim line remote
Hand held Slim Line Remotes come as 1 channel or 5 channel and are available in both black and white. They have table/wall support with a re-verso transparent bracket that allows the transmitter to stand on a table or to be fixed on the wall.
White Wall Mounted
Silver Wall Mounted
Black Wall Mounted
Surface Mounted control is a wireless wall switch and avoids cutting into drywall. It does not require an electrician. Available as single channel or four channel it is battery operated and easy to install. The remote can be used as a hand held or a wall mounted control simply by sliding on and off the surface mounted bracket. Available in white, silver, or black.
Slim Line Timers
available in both black and white. The timer is a multifunction remote with 90 channels display and timer. You can program up to 6 groups of 15 channels each. It also has a clear plastic wall bracket.
Wind Sensor ( Click To Enlarge)
SOL One Channel Remote
Wind Climate Sensors and Sun and Wind Climate Sensors are available and automatically control your motorized shades based on current weather conditions to help prevent damage. Please read Installation Instructions on the Installation Tab before installing these items. Wind sensors can be programmed to retract the shade between 6-31 mph. The sensors plug into a standard grounded outlet. You can set the shade limit stops with any QX5 remote. You so not need the SOL remote. If you have the Sun and Wind Sensor, you also need to order the SOL one channel remote to turn the sun sensor function on and off. It is best to have one sensor for each direction your shades are facing as the wind will come at the shades differently. When wind higher than your setting is sensed for a duration of 2 minutes, the shades will automatically retract. Once the wind speed has lowered to below your setting and has remained lower for 20 minutes, you will be able to control your shade with your remote. If you have the Sun and Wind Sensor, the shades will go down by themselves when the wind stops. Bear in mind that the 20 minutes is from when the wind is reduced. If it goes back above your setting before the 20 minutes is up it will be yet another 20 minutes before you or the sun sensor can lower the shade.
In other words, if you have the Sun and Wind Sensor, after the 20 minutes of calm, if the sun is still shining on the sun sensor, the shade WILL go back down.
If all you have is the wind sensor, it will not.
SOMFY MOTOR CONTROLS
Somfy offers a variety of ways to control you shades that go beyond the simple RTS hand held or wall mounted single and wall mounted remotes. Use the following information to select the right accessories to control your environment and safeguard your shades.
1 Channel Remote
Multi Channel Hand Held Remote (4 individual channels for shades or groups of shades, and one channel for 'all'
16 Channel Hand Held Remote
Wall Mounted 1 or 5 Channel-available white, ivory, and black. Wireless. We recommend that you also order a hand held remote to program your limit stops as it’s difficult to do with the wall mount units.
Wireless Wall Switch
The DecoFlex ™ RTS Switch is battery-powered and a completely wireless wall switch that provides an ideal way to control motorized products when entering or exiting a room. Available as either single or multi- channel it is available in white or ivory.
TIMER & REMOTE
If being used with one shade, the Telis 1 Chronis timer can be used to set the limit stops. For more than one shade you will also need the multi channel remote to set the limit stops.
The timer can be set to lower the shades once a day and raise them once a day.
If used in conjunction with the wind sensor, the wind sensor will raise them as described above, and you can lower them with your remote after the wind dies down, but the timer will not lower the shades again that same day as it only sends one ‘lower’ signal and one ‘raise’ signal per day.
SUN & WIND SENSOR
You must have a special ‘Soliris’ hand held remote to set the sun sensor, which can also be used to set your limit stops. Wall mounted remotes can’t set the sun sensor, so if you want one of those it would be in addition to the Soliris.
The wind sensor plugs in with a transformer and can control multiple shades. It is best to have one for each direction your shades are facing as wind will come at the shades differently.
You can set the wind speed anywhere from 6-31 mph.
When wind higher than your setting is sensed for a duration of 2 minutes, the shades are automatically retracted.
The sun sensor lowers the shade when it senses enough light. When the light dims (either because of nightfall, clouds, or shadows from trees etc.) the shades are retracted. If the sun sensor has lowered the shade, but the wind exceeds your setting, the wind sensor will over ride the sun sensor and raise the shade. Once the wind is reduced to below your setting for 15 minutes with the sun shining on the sensor, the shade will be lowered again.
Bear in mind that passing clouds and shadows will raise and lower the shade possibly many times a day, with the wind sensor also raising it for wind. You may disconnect the sun sensor and just operate it manually, but you can’t disconnect the wind sensor as the shade will then behave erratically, searching for a signal from the disconnected wind sensor every hour.
You must purchase the Soliris Remote for programming the Sun Sensor.
RAIN AND SUN SENSOR
You must have a special ‘Soliris’ hand held remote to set the sun sensor, which can also be used to set your limit stops. Wall mounted remotes can’t set the sun sensor, so if you want one of those it would be in addition to the Soliris. Solar-powered, so there is no need to plug the sensor in. We would recommend this for vinyl shades, when you want to have the shades lowered whenever it rains.
You can set the rain sensor from condensation/fog to heavy rain. Snow will also activate the sensor.
The sun sensor would be set to raise the shade when it senses enough light. When the light dims (either because of nightfall, clouds, or shadows from trees etc.) the shades are lowered. If the sun sensor has raised the shade because it is sunny, but the rain exceeds your setting, the rain sensor will over ride the sun sensor and lower the shade. This would take care of sun showers. Once the rain is reduced to below your setting for 2 minutes, with the sun shining on the sensor, the shade will be raised again.
Bear in mind that passing clouds and shadows will raise and lower the shade possibly many times a day, with the rain sensor also lowering it for rain. You may disconnect the sun sensor and just operate it with the remote, but you can’t disconnect the rain sensor as the shade will then behave erratically, searching for a signal from the disconnected rain sensor every 20 minutes or so.
MY LINK (App is free, but you buy the MyLink)
You must have a regular hand held or wall mounted remote to set the limit stops.
My Link is a smart phone app that you can use to control your shades from afar. You won’t have a way of knowing if your shade is up or down from the app; you would have to have some sort of home security camera for knowing this. If you use it with a wind sensor you would be able to lower the shade again with the app as long as the 15’ of reduced wind has gone by, again you would need to have a security camera that would tell you if the shade was up or down.
My Link has a built in timer that you can set for 5 scenarios (5 ups and 5 downs a day.) If used with a wind sensor and the shade was put up because of wind, you could have the shade automatically go down again at a preset time—as long as the wind was not blowing at that time.